Substrates
Can be applied over solvent-based basecoats and properly prepared paint surfaces in good condition.
Mixing Ratio
2 parts clearcoat to 1 part hardener.
Pot Life
1 hour at 23°C after mixing with hardener.
Spray Gun Tips
Nozzle: 1.3 mm
Conventional: 3.0–3.5 bar (45–50 psi)
HVLP: 2 bar (26–30 psi)
Spray Method
Application viscosity: 16–18 seconds (DIN Cup 4 at 23°C)
Coats: 2 to 3 coats, total film thickness 40–60 μm
Flash-off time between coats: 3–4 minutes at 23°C
Drying Time
At 15°C, the surface is dust-free in 25 minutes and polishable in 60 minutes.
At 23°C, it is dust-free in 20 minutes and polishable in 45 minutes.
At 30°C, it is dust-free in 15 minutes and polishable in 30 minutes.
Shelf Life
2 years in unopened containers when stored in cool, dry conditions.
Health and Safety
Refer to the Material Safety Data Sheet (MSDS) for full information.
Follow all precautionary labels and instructions on the container.
Ensure good ventilation in the working area.
Substrates
Suitable for application over AAS, PC/PET, PETP, PP-EP, and PP+EPDM plastics.
Mixing Ratio
Ready-to-use product — no mixing required.
Spray Gun Tips
Nozzle size: 1.2–1.3 mm
Conventional: 2 bar (26–29 psi)
HVLP: 2 bar (26–29 psi)
Spray Method
Apply 1 even coat
Flash-off time before overcoating: 15–20 minutes at 20°C
Drying Time
15–20 minutes at 20°C.
Sanding
Not required before topcoating.
Shelf Life
2 years in unopened containers when stored in cool, dry conditions.
Health and Safety
Refer to the Material Safety Data Sheet (MSDS) for full information.
Follow all safety instructions on the product label.
Ensure proper ventilation during use.
Substrates
Can be applied over 2K putties, 2K epoxy primers, 2K wash primers, 1K etch primers, factory primers, and well-sanded old finishes. For best performance, the surface must be sanded, cleaned, and degreased.
Mixing Ratio
By volume: 3 parts primer : 1 part hardener : 1–1.5 parts thinner
By weight: 4 parts primer : 1 part hardener : 1–1.5 parts thinner
Pot Life
30 minutes at 23°C after mixing with hardener.
Spray Gun Tips
Nozzle: 1.7–1.8 mm
Conventional: 3.0–3.5 bar (45–50 psi)
HVLP: 2 bar (30 psi)
Spray Method
Application viscosity: 16–18 seconds (DIN Cup 4 at 23°C)
Apply 2–3 coats, total film thickness 40–60 μm
Flash-off time between coats: 5–10 minutes at 23°C
Drying Time
24 hours at 15°C
12 hours at 23°C
60 minutes at 60°C
Sanding
Machine sanding: P320–P400–P500
Wet sanding: P800 or P1000
Shelf Life
2 years in unopened containers when stored in cool, dry conditions.
Health and Safety
Refer to the Material Safety Data Sheet (MSDS) for full safety guidelines.
Follow all safety instructions on the container.
Ensure adequate ventilation during use.
Substrates
Can be applied over properly prepared steel, weathered galvanized steel, hot-dip galvanized steel, stainless steel, aluminum, and existing 2K finishes in good condition. All surfaces must be sanded as recommended and thoroughly degreased with Vehicolor degreaser before application.
Surface Preparation
Steel Substrates
Blast cleaning, or
Mechanical sanding with P80–P180 grit, followed by degreasing with Vehicolor degreaser.
Galvanized Steel (Weathered/Exposed)
Degrease with Vehicolor degreaser
Sand with P180–P320 grit
Re-degrease
Hot-Dip Galvanized Steel
Degrease
Fine abrasion with P320 or finer grit
Re-degrease
Stainless Steel
Degrease
Profile with P180–P240 grit
Re-degrease
Aluminum
Light sanding with P240–P320
Final degreasing
Existing 2K Finishes (in good condition)
Light sanding with P320–P400
Re-degrease
Mixing Ratio
By volume: 3 parts epoxy primer, 1 part hardener, 1–1.5 parts thinner
By weight: 4 parts epoxy primer, 1 part hardener, 1–1.5 parts thinner
Pot Life
4 hours at 23°C after mixing
Spray Gun Tips
Nozzle: 1.7–1.8 mm
Conventional: 3.0–3.5 bar (45–50 psi)
HVLP: 2 bar (30 psi)
Spray Method
Application viscosity: 16–18 seconds (DIN Cup 4 at 23°C)
Apply 2–3 coats, total film thickness 25–30 μm
Flash-off time between coats: 5–10 minutes at 23°C
Drying Time
24 hours at 15°C
12 hours at 23°C
60 minutes at 60°C
Sanding
Dry sand after the coat becomes fully dry and solid using P600–P800 grit.
Shelf Life
2 years in unopened containers stored in cool, dry conditions.
Health and Safety
Refer to the MSDS for full health and safety information
Follow safety notices on the container
Ensure proper ventilation during application
Substrates
Can be applied over existing finishes and polyester putty. The surface must be thoroughly degreased before painting.
Mixing Ratio
1 part 1K primer to 1 part thinner (by weight).
Spray Gun Tips
Nozzle: 1.7–1.8 mm
Conventional: 3.0–3.5 bar (45–50 psi)
HVLP: 2 bar (30 psi)
Spray Method
Application viscosity: 16–18 seconds (DIN Cup 4 at 23°C)
Apply 2–3 coats with a total film thickness of 35–40 µm
Flash-off time between coats: 5–10 minutes at 23°C
Drying Time
45 minutes at 15°C
30 minutes at 23°C
Sanding
Wet sanding: P600–P800
Machine dry sanding: P400–P500
Shelf Life
2 years in unopened containers when stored in cool, dry conditions.
Health and Safety
Refer to the Material Safety Data Sheet (MSDS) for full safety guidelines
Follow all precautionary notices on the container
Ensure good ventilation in the working environment
Substrates
Vehicolor NC Filling Putty can be applied over 2K putties, primers, and old paints previously sanded properly.
Application
Apply by spreader. Apply in 1–2 thin coats.
When necessary, repeat the operation more times.
Allow drying for 5–10 minutes between coats.
Scrape Tool
Putty spreader
Drying time
25 minutes at 23°C
Sanding
Machine dry sanding: P400–P500
Manual wet sanding: P800 or P1000
Shelf life
2 years in unopened containers when stored in cool, dry conditions
Health and Safety
For full Health and Safety information please refer to Material Safety Data Sheet (MSDS)
Observe the precautionary notices displayed on the container
Good ventilation must be provided in the working environment
Substrates
Steel panel, galvanized panel, iron panel, aluminum panel, fiberglass.
Mixing ratio (Weight)
Body Filler: Hardener = 100:2
Layer Thickness
Putty can be applied in several thin coats. After each of them, the product should cure. Do not extend thickness of 5 mm.
Pot life
2–4 minutes at 25°C.
Application
Clean the surface of oil, rust, old paint, and moisture. Make sure it is dry and clean before applying the putty.
Mix the putty with hardener at a 100:2 ratio until the color is even. Use it within the working time; otherwise, it will harden and become unusable.
Apply the mixed putty to the repair area. It’s recommended to apply a rough base layer first, then a thin finishing layer to reduce pinholes.
After full curing, sand the putty surface to the desired finish.
Drying time
20–30 minutes at 25°C.
Sanding
Coarse sanding (dry): P80–P120
Finishing sanding (dry): P120–P320
Shelf life
1 year in unopened containers when stored in cool, dry conditions.
Health and Safety
For full Health and Safety information please refer to Material Safety Data Sheet (MSDS)
Observe the precautionary notices displayed on the container.
Good ventilation must be provided in the working environment.
Substrates
Steel panel, galvanized panel, iron panel, aluminum panel, fiberglass.
Mixing ratio (Weight)
Lightweight Body Filler: Hardener = 100:2
Layer Thickness
Putty can be applied in several thin coats. After each of them, the product should cure. Do not extend thickness of 5 mm.
Pot life
2–4 minutes at 25°C.
Application
Clean the surface of oil, rust, old paint, and moisture. Make sure it is dry and clean before applying the putty.
Mix the putty with hardener at a 100:2 ratio until the color is even. Use it within the working time; otherwise, it will harden and become unusable.
Apply the mixed putty to the repair area. It’s recommended to apply a rough base layer first, then a thin finishing layer to reduce pinholes.
After full curing, sand the putty surface to the desired finish.
Drying time
20–30 minutes at 25°C.
Sanding
Coarse sanding (dry): P80–P120
Finishing sanding (dry): P120–P320
Shelf life
1 year in unopened containers when stored in cool, dry conditions.
Health and Safety
For full Health and Safety information please refer to Material Safety Data Sheet (MSDS)
Observe the precautionary notices displayed on the container.
Good ventilation must be provided in the working environment.
EN
ES